Grand Banks 52 for sale

Walkthrough

The large covered aft deck is a spacious area and very comfortable for several deck chairs and room for a table.  At the transom there is a Novurania 400DL RIB tender located on a Freedom hydraulic dinghy lift so its just a push of a button to launch and retrieve her. She also is equipped with a Marquipt 800-lb. davit located to aft on the flybridge.  A staircase from the aft deck to the flybridge leads to an expansive area with new Sunbrella Bimini top on a double stainless steel frame. Forward on the bridge there is an expansive L-settee to starboard with a beautiful GB teak table. Her helm is center with a new Stidd helmseat and additional seating is to port.  All flybridge cushions and covers are new March 2021 and a new stainless steel propane grill was installed in 2021.

Entering the salon from the large covered aft deck either through the wide sliding aft deck doors or via forward port and starboard pilothouse doors at the helm. The bright and open salon boasts teak parquet floors and a richly-upholstered L-settee new March 2021 with teak yacht table with built in cup holders to starboard. To port is a straight settee. All seating features storage beneath and the interior has received new upholstery in Dec 2020. A custom corner entertainment system cabinet is at the aft bulkhead. Moving forward, her large well-equipped U-shaped galley is to starboard opposite the port dinette area. The galley offers an abundance of storage with features such as overhead lockers that drop down for plate and glass storage as well as in counter storage.  In the past year the galley has seen a custom refit with new stainless steel upright refrigerator and freezer, new stainless steel ice maker and custom stainless steel stove and oven with overhead vent.  When the new appliances were being installed a custom marine carpenter added a spice rack drawer, pots and pans drawer and beautifully done silverware and cutlery drawer.

The lower helm features a full suite of electronics (repeated on the flybridge) including a new Garmin radar and KVH SAT TV in 2021, large integrated chart locker, new Stidd helmseat and comfortable double guest seating to port and starboard with footrest. To port of this helm station is a companionway to access the three Staterooms below.

Down the companionway to port of the lower helm is access to the Staterooms and Heads. Below is the landing and aft is the private and voluminous full-beam Master Stateroom with queen island berth bordered by night tables with reading lights. There is a straight settee to starboard and built-in vanity and storage drawers to port. Large hanging lockers are positioned on both port and starboard. The en suite Master Head has a VacuFlush toilet and sink to starboard and a separate stall shower room to port allowing for simultaneous use of these areas while maintaining privacy.

The VIP Guest Stateroom forward features a V-berth with filler/insert so it can be one huge berth or separated easily into two singles. There are built-in drawers, night tables and reading lights. There is plenty of storage throughout with integrated cabinets, drawers and a custom cedar-lined hanging closet. Natural lighting is provided through portholes with an overhead hatch. Shades are installed on all portholes and hatch.

The second Guest Stateroom with athwartship oversized double berth to starboard also has a cedar-lined hanging locker and additional storage. The shared Guest Head is to port with stall shower.

Open the large hatch on her aft deck and you have a perfect storage space. On the port side are the full-size separate washer and dryer units. Moving forward is her engine room access. Once through the entry door, you have full stand-up headroom. Everything in this area is easy to get to and in impeccably nice condition.

There is an extensive spare parts kit onboard with almost anything anyone would want to have onboard for long-term cruising. 

Crosswinds is an incredibly well cared for Grand Banks 52 Europa. The boat has been highly updated and carefully serviced to keep her in pristine condition in every way.

Exterior Equipment

Air horn
Anchor, Port Galvanized Bruce SL/Claw 66-lb. with 200' 3/8"S/S chain
Anchor, Stbd Galvanized CQR Plow 75-lb. with 100' 3/8" S/S chain and 100' 5/8 nylon 3-strand rode
Anchor chain locker, divided for rope & chain
Anchor platform, fiberglass, with pulpit
Anchor windlass locker, fiberglass
Ball valves on thru hull above waterline, bronze
Bow pulpit with dual anchor rollers
Canvas Covers, Sunbrella ? Flybridge helm, seating, tender & windlass; Tender
Chocks and cleats, stainless steel
Courtesy lights, side decks
Deck fillers, diesel fuel and water, S/S
Engine room vents
Flagstaff holders, bow and stern
Fresh water outlet, fwd
Grab rails, stainless steel
Inspection deck plate for fuel tanks, port & stbd
Navigation light boards, Teak
Mast, hinged, FRP ? supports radar & bracket, anchor/steaming lights, windex array, SAT TV receiver dome & remote GPS antenna
Rail gates at port and starboard
Safety rails on main deck, stainless steel
Stanchions, stainless steel
Step plates at rail gate openings
Vents for fuel and water tanks
Waste pump-out deck fittings, stainless steel
Lofrans Falkon Windlass, horizontal, rope/chain, three-station, 12V/1500W

Aft Deck

Staircase to flybridge, molded fiberglass w/louvered door for storage inside
Rail gate
Safety rails, Teak or stainless steel
Sliding hatch to F/B with Teak frame
Swim platform, extended, Teak
Swim ladder
Transom, Teak
Transom door
Transom shower with retractable hose hot/cold
Novurania 400DL RIB tender with Yamaha 50hp outboard motor

Flybridge

Alarm panel, engine temperature and oil pressure
Compass
Deck - main in Teak, side and rear in non-skid
Electronics locker
Chart Locker
Helmseat
High Water Alarms, Rule
Instrumentation raised dashboard, fiberglass
Outlet, 12V DC
Rail around flybridge windshield, stainless steel
Safety rails, stainless steel
Seats with cushions, port & stbd
Settee-L with cushions and Hi-Lo table, Aft
Steering wheel, Teak with stainless steel rim
Storage boxes under seats with Teak grating
Storage locker moulded behind L-settee
Windshield New Stainless Steel Propane Grill

Electronics and Navigation

New Garmin 48NM Radar(2) Garmin 15" Touchscreen Displays with Chartplotter and Sounder (1 at Upper, 1 at Lower)(2) Hydraulic Assist Steering Systems, Teleflex Capilano (1) at each helm
Autopilot, Simrad RPU300 12V/hydraulic pump controls at each helm
Trim Tabs, Bennett ? toggle control panels at each helm
Bow Thruster, Side-Power SP-155-TCI, 20hp/24V joystick panels at each helm
Stabilizers, Naiad, 24V, 1250psi, digital MultiSeaII controls at each helm
Compass, Ritchie PowerDamp+ (1) at each helm
Simrad AP20 Autopilot  (1) at each helm
ICOM IC-M422 VHF at Flybridge
Horizon VHF  (1) at each helm
Simrad IS15 depth display (1) at each helm
Jabsco remote searchlight control  (1) at each helm
Garmin GND10 Instrument/Display interface switch box
Garmin GSD-22 Depth Sounder Processor at Lower Helm
FireBoy Xintex FR-1000 CO monitor display at Flybridge
Bennett Trim Tab control toggle panel at Flybridge
Rule high bilge-water audible alarm at Flybridge

Engine and Mechanical

Twin CAT 3208s @ 435hp each with 3727 hours as reported 3-10-22 Twin Disc MG 5061A Transmissions with 2.47:1 RatioFull Engine Cooler Service Performed July 2022Turbos Blueprinted and Resealed July 2022
Bow Thruster, Side-Power SP-155-TCI, 24VGlendening SynchronizerAir Conditioning, MarineAir, (5) units
Aquadrive anti-vibration system w/matching engine mounts
(3) Bilge pumps, 2000 gph
Whale manual diaphragm pump
Drip pans under engines
Engine raw water intake strainers
Engine room sound insulation
Engine start-stop at Lower Helm
Exhaust system, sea-water cooled
Fireboy Fire System
(5) Fire Extinguishers in Galley, Salon, Master Stateroom, Engine Room &
Flybridge
Fresh water outlet in engine room
Fuel filters, Racor
Fuel manifold system
Fuel tanks, mild steel, baffled
Fuel tanks with upper & lower automatic self-closing valves for sight gauges
Panish dual lever controls
Propellers, bronze
Spare Props
Propeller shafts, stainless steel
Rudders, fiberglass
Seacocks on all thru-hulls below waterline
Separating filters, fuel-water
Thrust Bearings, Aquadrive
Dripless Shaft Seals, Norscot
Stabilizers, Naiad
Steering, hydraulic
Struts, bronze with rubber bearings
Throttle and gear shift controls, dual station
Trim Tabs, Bennett
Central Vacuum System, Beam
Water tanks, marine aluminum
Water/gas separator installed on generators exhaust system
Watermaker, FCI AquaMiser+, 600 gal/day, Upgrade

Electrical Systems

Newer (2019) Onan Generator with Sound Shield, 21.5kw, 679 hours New (2021) Onboard Solutions 2000w TruePower Inverter
Alternator, each engine
Batteries, (2) 8D, (3) Deka Deep Cycle and (1) Group 24
(2) Battery chargers, Professional Mariner 50-amp
Battery selector switch
(4) Bilge pumps, automatic, 12V and (1) manual
Bonding system
Cable, tinned-copper
Circuit breakers on all circuits
Engine room blowers, 12V
Engine room lights, 12V
Fresh water system, pressurized, 12V
Galvanic isolator
Generator amp and volt meters
Generator compartment exhaust blower, 12V
Ground fault circuit interrupters
Holding tank with pump out, 12V
Indicator light, bilge pump
Indicator light, reverse polarity
Navigation lights, 12V
Shore power inlets, 50-amp 220V AC, fwd & aft
Spreader lights on mast, 12V
Washer and Dryer, Whirlpool
Water heater, Seaward 20-gal
Zinc saver isolator

Updates and Upgrades - Previous and Current Owners

2017

01-12-17 Replaced 3 house batteries ($280 each), 2 starter batteries, 2 12-volt thruster batteries ($523 each), generator battery, dinghy battery
01-12-17 Acid flushed 5 AC units ($382)
01-16-17 Complete maintenance on VacuFlush system; New motor on starboard head; New valves, duckbills, etc.
01-19-17 Repaired tachometers (2)
01-23-17 Maintenance/certification on Firebox and 4 CO2 fire extinguishers.
02-03-17 Fix Fusion system on bridge and anchor light switch
03-03-17 Bottom paint/zincs/etc. ($5,703) Coral Bay Marina
03-03-17 Bi-annual maintenance on stabilizers ($1500) Stabilized Mar
03-06-17 Hot water tank hose connection leak repaired ($290 John Hall)
03-15-17 (3219) Replaced the 6 engine zincs
03-17-17 Full detail?compound, wax, teak, metal polishing. ($3600) Jolene. $50 ft x 55, plus for hull and topside bridge area
03-24-17 Fiberglass repairs/selective painting ($1200 Ben Dill)
03-20-17 Watermaker; Installed new membrane.; New low pressure gauge; ($600 SALT?Chris)
03-24-17 Dinghy Annual service ($1700 J&B Marine)
04-06-17 Dinghy Annual; Wiring; Lights; Sump pump; etc. ($1,736 J&B Marine)
04-07-17 Watermaker Membrane; LP Gauge; Filters ($600 SALT)
05-06-17 Spare Cat Seawater pump ($1,111.62 John Hall)
05-06-17 Spare Cat Alternator ($341.41 John Hall)
05-06-17 Replace engine heat exchanger end caps ($60 John Hall)
05-06-17 Fill fuel tanks P=564 S=529 (Engine hours 3219)
05-11-17 Replaced Starboard Water pump as a precaution
05-17-17 Replaced GenSet Seawater pump ($500 J. Hall)
08-02-17 Replaced hot water heater ($1,716 Aquatech)
09-04-17 Teak deck refinishing/Repair ($11,175 Christian Mikkelsen)
11-06-17Replace Watermaker Membrane ?ordered new solenoid ($430 SALT?Chris)
11-17-17 Replace G-Wind
12-09-17 Replaced all zincs
12-09-17 Varnished boat 3 coats (Baldy $4200) Last time (01-16-16) 2 coats $3600
12-17-17 Paint wings (4) cracking/discolored (Baldy $2300)
12-17-17 Dinghy Cleaned injectors, replaced rusted engine/battery/throttle cables ($2000 J&B Marine)

2018

01-18-18 Replaced AC controller with new Passport I/O on Mid-Salon Unit ($400 SALT?Chris)
01-11-18 Replaced Starter Batteries; AGMs ($1700 J. Hall)
01-11-18 Replaced ProMariner Starter Battery Chargers and 60 AMP Breaker ($800 J. Hall)
01-18-18 Replaced mid salon AC controller ($400)
04-23-18 Replaced Starboard engine impeller (eng: 3300 hrs) Water pump OK. No leaks. Impeller was OK too. (Hall)
04-28-18 Replace controller on mid salon AC (SALT $322)
05-07-18 Fireboy, extinguisher updates; Monroe County Fire Equipment )$338.63 Robert Dillon)
05-06-18 Replaced GenSet fuel pump (Hull)
05-08-18 Replaced Port leaking water pump. (Hall)
05-08-18 Replaced seawater pump assembly ($1,112 Hall)
05-08-18 Replaced generator impeller (Hall) ­­­____hrs.
05-10-18 Full detailing/metal?1 step Vibra, 2-step Awesome Buff, 3 step Vitreo ($3560 Jolene Durstin)
06-05-18 Dinghy annual maintenance (J&B $929)
06-13-18 (3334) Check all belts/replace eng rm light (Hall $1250)
07-10-18 Replace port head bellows (Chuck installed) ($339 Nassau)
08-07-18 Replace AC Water Pump Assembly; Hole in housing (Hall $1,045) Entire pump replaced 9/23/15 for $1,500 by Hall)
08-10-18 Replaced starboard head bellows/bought spare ($1900) Replaced gauges for both heads ($1500) (Key Boatworks Tom)
08-17-18 KVH Antenna fuse. (Seamark Electronics)
09-05-18 Air filter/gaskets/hoses?valve adj. clean/reseal trans coolers; Rebuild oil cooler (stbd) Change transmission oil. Flush engs (Diesel Doc $5,077.47---labor $3875)
09-05-18 New Robertson AP 20 Autopilot for Bridge ($1500 Motion Marine) Installed
10-26-18 Roballo troubleshooting; VHS/Starter battery connections loose; Battery and trim switches replaced (J&B $528)
11-19-18 Fireboy shutdown systems (Seacoast $3,100)

2019

01-02-19 Promatic charger ($626) & other electrical (Hall $2,533)
01-03-19 Salon TV ($500)
01-09-19 Glasstech
Bottom Paint, etc. $7,193
Bent prop work $1,200
Underwater lights $2,190
Paint bottom stripe $1,20
Plus misc. electrical work; Total bill $21,070
01-09-19 Stabilizer Maintenance Stabilized Marine ($1,250)
01-10-19 G3 Garmin Vision Map West Marine ($399)
02-01-19 New Salon AC Unit (SALT $605 + $2000+)
2-10-19 Battery isolator, switches, GFI's, etc. (John Hall $1310)
03-05-19 New Onan 21.5 MDKDR Generator (Ted Kaster $25,466.80)
2020

02-01-20 Teak Refurbishing (Christain Mickelson $6,350)
04-06-20 Changed out all zincs?weren?t too bad
06-18-2020 Replaced 3 house batteries (John Hall $1,500)
07-15-20 Bottom paint/speed prop/zincs/grind & fill spots ($6,500). PPS shaft seals ($2,900), replace port cutlass bearing ($2,700), detail to rub rail ($900) -Total bill: $13,055.
11-18-20 Replace compressor in refrig (SALT $2,360)
12-15-20 Re-upholster interior (fabric $3000/labor $5,500)

2021

• 
  
• 01-12-21 \ Dinghy - Replace worn steering cable, step pads and zincs. (J&B Marine $1,100)
• 02-08-21 Sunbrella Bimini top, bridge chair, tables and cushions (Cover Emporium $7,000)
• 02-15-21 Strip bare and varnish back stern teak panel (Campbell)
• 05-28-21 Replaced all sanitation hoses (RB Marine)
• 05-28-21 Install New Inverter (RB Marine)
• 05-28-21 Replace EPIRB Battery (RB Marine)
• 05-28-21 Re-secure Rub Rails (RB Marine)
• 05-28-21 Re-bed compound around opening ports (RB Marine)
• 05-28-21 Repair Port and Starboard Running Lights (RB Marine)
• 05-28-21 Replace Mid-Salon Air Conditioning Unit (RB Marine)
• 05-28-21 Cleaned Air Intakes for All A/C Units (RB Marine)
• 06-01-21 New Throw Rugs - Salon, Galley, Wheelhouse (Talbot $3,409)
• 07-22-21 Repair V-Berth AC Pressure Switch (Oxford Boatyard)
• 07-22-21 Repair Master Shower Sump (Oxford Boatyard)
• 07-22-21 Replace GFCI in Master Stateroom (Oxford Boatyard)
• 07-23-21 Garmin Software Update (Oxford Boatyard)
• 07-26-21 Tender Outboard Work- Fuel Rail and Injectors, Replace Filter and Gaskets, Change Fuel Filter, and Prime (Oxford Boatyard $1310)
• 07-27-21 Replace Garmin Radar GMR24XHD (Oxford Boatyard $3722)
• 08-08-21 Custom V-Berth and Guest Bedding (All Aboard $1500)
• 08-11-21 (2) New Stidd Helm Chairs (Stidd $8,847)
• 08-16-21 Repair Shorepower Ground Fault (Oxford Boatyard)
• 08-20-21 Install New KVH TV3 SAT TV (Oxford Boatyard $3,995)
• 08-23-21 Change Both Engine Impellers (Oxford Boatyard)
• 08-24-21 Change Both Engine Oil and Filters Hours Port 3,599 Starboard 3,603 (Oxford BY)
• 08-24-21 Install the New Stidd Seats (Oxford Boatyard)
• 08-24-21 Refresh AC Seawater Pump (Oxford Boatyard $1,450)
• 08-31-21 Strip and Varnish Toe Rail and Eyebrow with 5 Coats ($17,879 Oxford Boatyard)
• 09-01-21 New Isotherm Icemaker (Isotherm $1,729)
• 09-01-21 New Range and Stove (Avanati $2,109)
• 09-01-21 New BBQ Grill (Solaire $2,305)
• 09-01-21 New Refrigerator (Vitrifrigo $1,982)
• 09-15-21 Sand and Varnish Toe Rail and Eyebrow with 3 Additional Coats (Oxford $6,537)
• 09-17-21 Check and Caulk Port Lights (Oxford $1618)
• 09-21-21 Detail, Compound and Wax Boat (Oxford $5,159)
• 09-24-21 Clean Teak Decks (Oxford $2013)
• 09-27-21 New Cushion for Bridge and Canvas Stidd Cover (Windy's Upholstery $653)
• 10-13-21 Convert Generator to 120/240v, New Breaker for New Stove (Oxford $2,553)
• 10-15-21 Replace 110V Light Fixtures in Engine Room  (Oxford $1274)
• 10-19-21 Replace Control Board on Lower Helm AC (Oxford)
• 10-21-21 Labor to Replace New Galley Appliances and do Custom Cabinetry Work (Oxford Boatyard $20,581)

Disclaimer

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.

*Back Available on Market! "Crosswinds" had a prolonged deal go south for buyer financing issues and is now an even better opportunity!  Fresh Engine Cooler Services have been performed on her CATs and both turbos blueprinted and resealed.  She is standing tall and ready for her next owner to enjoy!*
"Crosswinds" is an exceptional example of the legendary Grand Banks 52 Europa.  Maintained and upgraded by an experienced owner she has seen the best of care and is ready to be enjoyed and cruised.  With proven seakeeping and outstanding construction she is the complete package.  The 52 GB offers a one level main deck that flows from the large aft deck into a bright and open salon, updated galley with dinette and pilothouse forward.  Below is a three stateroom, two head layout with a full beam master stateroom.  On the exterior there are wide covered side deck, stairs that lead to a huge flybridge and upper helm.  The stand up engine room and well laid out engine space complete the package. Numerous features include:

• Bow Thruster
• Naiad Stabilizers
• New 21.5kw Generator
• Updated Garmin Radar with Garmin Touchscreen Chartplotter
• Updated KVH SAT TV
• New Galley Appliances
• Custom Galley Countertops
• Freedom Lift Hydraulic Tender Lift
• Novurania 400DL RIB tender with 50hp Yamaha Four Stroke 
• 800 lb Marquipt Davit
• Updated Interior and Exterior Softgoods
• New Stidd Helm Chairs at both helms
• Underwater Lights
• Fresh Varnish and Gleaming Gelcoat